How to connect P-Trap to Wall Drain | Best & Cheapest Way

The p-trap is a necessary part of your plumbing that helps to keep sewer gases from entering your home. 

It’s a U-shaped pipe that connects the drain pipe from your sink or shower to the main sewage line, and it should be checked regularly for leaks and proper function. 

If you notice any problems with your p-trap, try to fix it yourself. Read on to know how to connect p-trap to wall drain!

What is the P-trap in a toilet? Mechanism of P-trap?

The p-trap is a plumbing fixture used to prevent the escape of sewer gas and vermin from the drainage system. 

It consists of a curved section of pipe that is fitted below the sink, and it traps water in order to create a seal that blocks the passage of gas and pests.

What is P-trap used for?

The reasons for getting a plumber to install a p-trap at your apartment or house are:

1. Saves your time and effort.

2. Prevents gas and vermin from the central drainage system.

3. Installation is hassle-free; no experience is required.

Advantages of P-trap?

-P-traps help keep your plumbing lines clean by trapping debris and preventing it from entering the drainage system.

-They also prevent foul odors from emanating from the drains.

-P-traps are a vital part of your plumbing system and should be installed on every sink, shower, and toilet. By doing so, you will keep your drains clear of any debris and prevent foul odors from entering the room.

-The p-trap is one of the most important elements in your bathroom. It’s meant to keep standing water in your drain lines, therefore preventing the bad smells and potential damage from those bad smells.

-Over time, p-traps can become corroded or damaged and need to be replaced.

How to connect P trap To wall drain

The first thing that you must be very careful about while installing the p-trap is to avoid any damage to your drainage system. If the drainage becomes damaged, you will have to install a new drain, which can be really expensive.

The p-trap is used as a kind of barrier designed to trap water and sewer gas. The main house drain/drainage system should be turned off first.

· If there are any leaks in your drainage, this would immediately cause a big problem.

The next step is to disconnect the drainage from your sink. Once you have successfully removed the drainage, then it will be time to remove all of the old pieces of the p-trap. 

You will need a pipe wrench tool to loosen the fittings and tubes, etc.

After you have removed all the old pieces of the p-trap, it is time to fit the new components. The hole in your sink will be used for passing the new p-trap. 

Most of the sinks come with a hole that is perfectly sized to fit the components of the p-trap.

An additional hole for attaching the P-trap would need to be drilled.

The components of the p-trap generally require a 3-inch hole to fit through. You can then insert the p-trap into your sink.

There should be an overflow hole in your sink, and if you are using one, then it must be covered with a stopper plate. 

This can be done by removing the cover on the overflow hole and then screwing down the cover on top of it. 

Now you will need to install a clean-out plug into your new overflow hole. Then connect the P-trap to this clean-out plug with a PVC connector.

Now you will need to attach the p-trap to your sink drain. Just screw in the nut and thread it on by hand, and then use a wrench to tighten it up. 

The last step is to connect the drain line to your P-trap. This part is essential; otherwise, you will have a big problem if it gets loose. You then need to tighten it up with a pipe wrench. 

Now you can check your work by filling the sink with water, and if everything is holding up perfectly, you can try flushing the toilet to see if there is any leak. 

Now you need to open the water main and check for any leaks.

That’s all you need to do if you want to know how to install a P-trap at your house or apartment by yourself. 

Wear all of your safety equipment and follow all of the directions.

How does the P-trap connect to the wall?

The P-trap connects to the wall by using screws inserted into the wall. The screws hold the P-trap in place and keep it from moving. 

If the P-trap is not appropriately connected to the wall, water could leak behind the walls. This could be a major issue because it would cause mold growth and damage drywall. 

Suppose you wonder about your P-trap, including how to fix it or why it is leaking. In that case, this article provides information on what you need to know so that you can fix it yourself.

Read More- how to remove the object from toilet trap

How does a P-trap Work?

A P-trap is a U-shaped pipe inside the toilet tank that traps air and water to prevent sewer gases from entering your home or office through the drainage pipes. 

The trap holds the water, which creates a seal preventing odors from passing through. 

The most important part of a P-trap is the curve because it traps the water in between two points. This creates a seal so that sewer gases cannot pass through your drainage system.

What is the name of the fitting that connects the p-trap to the drain?

The fitting that links the p-trap to the drain is known as a “drain trap.” It is also known as an “S-trap” at times.

It is called an S-trap because the water flows through it in an “S” shape. The water starts at the drain, moves up and over the “S” shape, then back down into the pipe, which leads to the sewer line.

How do you attach P-trap to metal wall drain?

The drain pipe from the sink to the trap should be as short and straight as possible. If there is a long horizontal run, a larger diameter pipe will need to carry the water flow without causing a siphon effect.

When you have the drain assembly in place, use a level to ensure it’s horizontal. 

Mark the locations of the screws on the wall and drill pilot holes. 

Attach the trap with screws and washers provided. Tighten them firmly by hand – do not use a tool that will damage or distort the trap threads. 

Finally, attach the tailpiece to the drain outlet on the sink and tighten it by hand.

Noisy pipes and the resulting vibrations can be reduced by using a rubber washer around each metal screw. Apply plumber’s putty to the washer, then screw the tailpiece into place.

Finally, slip the overflow cover over the tailpiece outlet and tighten it with a screwdriver. That’s all there is to sink drain installation!

How to Diagnose a Leaking P-Trap

P-traps can be accessed in crawl spaces, basements, or in the ceiling of the bathroom. 

C-clamps hold the p-trap to the drain line, and their rubber gasket prevents leaking. When this seal is compromised, the p-trap will leak, and water will accumulate in the dishwasher or sink cabinet.

How to Fix a Leaking P-Trap

If you notice leaking from your p-trap, turn off your water supply and disconnect the line from your sink faucet. 

Turn off your water heater as well. 

After turning off the water, remove the c-clamp and take the p-trap out of the drain line.

Inspect your rubber gasket for any signs of deterioration or damage and replace it if needed.

Read more- Why toilet flushes slow but not clogged

How to Replace a P-Trap

Over time, p-traps can become corroded or damaged and need to be replaced.

How to Replace a P-Trap with a Dishwasher Connection

P-traps can be accessed in crawl spaces, basements, or in the ceiling of the bathroom. C-clamps hold the p-trap to the drain line, and their rubber gasket prevents leaking. 

When this seal is compromised, the p-trap will leak, and water will accumulate in the dishwasher or sink cabinet.

How to Replace a P-Trap with a Garbage Disposal Connection, Shower Connection, Toilets Connection 

-Garbage disposals help reduce your kitchen waste and odor by grinding up food into smaller pieces. However, they can be a problem if not properly ventilated.

-If your garbage disposal makes loud noises, has bad smells coming from it, or slows down, you may need to replace the p-trap under the sink.

Check more- Best 19 inch toilets